tag:blogger.com,1999:blog-1208920363506659599.post5018461135958168047..comments2024-03-04T13:04:34.978-06:00Comments on Howdy Ya Dewit!: Fixing a Busted Old StripperTom Kinghttp://www.blogger.com/profile/16700342512275624543noreply@blogger.comBlogger8125tag:blogger.com,1999:blog-1208920363506659599.post-44157699641578893002021-10-08T18:21:30.676-05:002021-10-08T18:21:30.676-05:00You might inject more fiberglass resin and hardene...You might inject more fiberglass resin and hardener(follow the directions on the container). Fill up the bubble. Or you can sand it off and layer on another fiberglass cloth and resin/epoxy coat to make it lay flat. Fiberglass is pretty forgiving that way.<br />Tom Kinghttps://www.blogger.com/profile/16700342512275624543noreply@blogger.comtag:blogger.com,1999:blog-1208920363506659599.post-36500251356412544702021-10-07T15:20:57.830-05:002021-10-07T15:20:57.830-05:00I built a cedar strip canoe in 1984: there is a se...I built a cedar strip canoe in 1984: there is a section of fiberglass that has bubbled up on the bottom and just started up around the curve on one side. Is there a "glue" that I can inject into that bubble and make that adhere to the canoe. I'm not ready to retire the canoe just yet. Thanks for any information. DennisDennishttps://www.blogger.com/profile/07785035737177904170noreply@blogger.comtag:blogger.com,1999:blog-1208920363506659599.post-68529108996479435792021-03-08T03:49:25.509-06:002021-03-08T03:49:25.509-06:00Simply wish to say your article is as astonishing....Simply wish to say your article is as astonishing. The clarity in your post is simply great, and I could assume you are an expert on this subject. Same as your blog i found another one <a href="https://sohman.com/epoxy/" rel="nofollow">Sohman Epoxy </a>.Actually I was looking for the same information on internet for <a href="https://sohman.com/epoxy/product/solvent/bca/" rel="nofollow"><br />Nitibha kaulhttps://www.blogger.com/profile/10712012076275609458noreply@blogger.comtag:blogger.com,1999:blog-1208920363506659599.post-10061142934613314342019-09-17T05:33:26.399-05:002019-09-17T05:33:26.399-05:00Took me time to read all the comments, but I reall...Took me time to read all the comments, but I really enjoyed the article. It proved to be Very helpful to me and I am sure to all the commenters here! It’s always nice when you can not only be informed, but also entertained! <a href="https://www.kitchenfaucetguides.net/" rel="nofollow">kitchenfaucetguides.net</a><br />saadhttps://www.blogger.com/profile/01268916220539938415noreply@blogger.comtag:blogger.com,1999:blog-1208920363506659599.post-55542604422726320152015-05-07T10:46:08.540-05:002015-05-07T10:46:08.540-05:00If the holes on the outside aren't bad and you...If the holes on the outside aren't bad and you aren't worried about looks, a little wood filler and whatever finish the boat is coated in should make it water tight. You can always cover the holes on the inside with a fiberglass patch. If you want to make the holes go away, you'll have to replace the strips, but if you're not fanatical about the looks of the thing, you shouldn&#Tom Kinghttps://www.blogger.com/profile/16700342512275624543noreply@blogger.comtag:blogger.com,1999:blog-1208920363506659599.post-33922338770787852932015-05-07T10:10:17.274-05:002015-05-07T10:10:17.274-05:00Have a stripper with 4 small holes that was mounte...Have a stripper with 4 small holes that was mounted inside. Can I make this water tight w/o replacing strips? Thanks, DanAnonymoushttps://www.blogger.com/profile/07890254717722239162noreply@blogger.comtag:blogger.com,1999:blog-1208920363506659599.post-8904901749697853032014-11-04T14:37:54.235-06:002014-11-04T14:37:54.235-06:00Eric: It rather depends on the underlying framewor...Eric: It rather depends on the underlying framework of your rowboat. How far apart the ribs are primarily. In a cedar strip canoe, the ribs are fairly close together. I like for the replacement strips to span two ribs for support from below. It's not essential that the strip end directly on top of a rib so long as the unsupported length beyond the rib isn't more than a few inches and Tom Kinghttps://www.blogger.com/profile/16700342512275624543noreply@blogger.comtag:blogger.com,1999:blog-1208920363506659599.post-33247288034851180122014-11-04T11:12:11.388-06:002014-11-04T11:12:11.388-06:00Does it matter where the ends of the replaced stri...Does it matter where the ends of the replaced strips are relative to the underlying ribs when I repair my cedar strip rowboat?Anonymoushttps://www.blogger.com/profile/11260225614771430269noreply@blogger.com