Monday, December 07, 2009

The Old Cane Pole

When I was a kid coming up in rural Texas, everyone took a stab at fishing. It was a right of passage as sacred as learning to ride a bicycle, sneaking out behind the barn to try out a stolen cigarette or stealing watermelons. While I did learn to ride a bicycle without parental assistance, I skipped becoming addicted to nicotine in junior high school and missed out on the educational experience of plucking rock salt out of my buttocks with a pair of pliers. Local farmers were always armed in those days. This was before the time of the hippie farmer.

Fishing, however, I did try, sitting on the muddy red clay banks of creeks and stock tanks with a peach can full of worms I'd dug up out of the back yard. Cane pole fishing is a sport that requires patience and for and ADD kid like me the only thing that made it work was that creek born perch were hungry little devils, if not very big. Even on a bad day that red and white “bobber” would be jerked under about every 15 or 20 minutes and old-fashioned fishing action would ensue.

I never ate them in those days. Mom didn't much like fooling with fish and I didn't much like cleaning them, so most of my catches went back into the water. Some of them must have been pretty hungry because I've spent more than one afternoon pulling the same fish out over and over again. All the fun you could want with nothing more than a rusty hook, a length of fishing line and a simple bamboo cane pole.

Despite it’s simplicity, the old-fashioned cane pole is a deadly fishing tool, rivaling more expensive modern rods of fiberglass and graphite. In fact, since I graduated to rod and reel and fishing lures, my catch rate has decreased dramatically. That's all right with me since I still don't like to clean fish and I find as I age that my sympathies have begun to lie with the fish. Mostly I fish now for something to do with my hands while I sit in boats. The fact that the $5 fishing lure I'm dragging back and forth through the water isn't fooling any fish is immaterial to me. I just like watching the “realistic action” as I drag the danged thing through the water.

For those of you who actually want to catch some fish, though, a bit of fishing line, a bobber, a lead weight and a worm, is all you need to create a low cost, but effective tool for bringing home a nice fish dinner. A homemade cane pole is something every kid needs to make at least once in his life no matter how old the kid might be. Besides, it's siimple to do – a factor that becomes more and more important to some of us older “kids”. Here is what you need to do.

Cut yourself a bamboo cane pole about 8 to 10 feet long. Use a fine toothed saw to get a clean cut on the butt end. You can, of course, buy one, but where's the fun in that. Better to find a grove of golden bamboo somewhere. You can find them everywhere since somebody decided to import bamboo to America as a low cost building material more than a century or so ago. There's hardly a part of the country now where bamboo doesn't grow wild somewhere. The free poles you find growing in a stand of bamboo in some grader ditch are much more fun than store bought ones. You get to brag that you found this one growing wild and you “cut it yourself”. Hey, we take our bragging rights where we can get 'em these days.

Choose a pole about 3/4 inch in diameter at the base. The pole should be 8 to 10 feet long and about 1/4 in diameter at the tip. Golden bamboo is the best. There are other varieties, but the yellow-green “golden” variety makes the best fishing cane poles. The joints tend to be close together at the base of this variety, adding strength and little indentations that make for a perfect handgrip. Cane poles have long tough fibers that will support a surprisingly large fish, while providing the flexibility to work him on the end of the line without losing him.

If you do cut your own pole, saw it off down close to the ground where the base is heavy and strong. Once you've cut it, give the taperd end a quick whip back and forth to insure there are no cracks or splits in the shaft that you didn't see before.

The next step is to dry your pole since it's going to be too green to use after it is first cut. Drill a hole in the base and run some wire through it to make a hook or loop. Hang the pole upside down by the hook in a sunny warm place on the side of a building, tower or tall tree. Make sure it gets plenty of sun every day. Tie a brick to the tip to weight it down so it will dry straight. The pole should hang for 1 to 3 weeks.

When the pole is dry use a torch, hair dryer or open flame to heat the pole. Be careful not to burn it. The heat will drive any oil or wax within the pole to the surface. Heating will leave a greasy grey waxy film over the pole. Let it coola dn when it turns clear, you can wipe away the residue with a dry rag.

Next, use steel wool or fine sandpaper to rough up the surface. Then wipe off the dust and stand the pole in a warm dry place for a few hours.

Next, brush on a couple of coats of marine spar varnish, allowing the finish to completely dry between coats. The varnish helps keep moisture out of the pole, protects against water damage and cracking and gives the pole a dark sheen that looks nice.

When your pole is ready, tie on enough fishing line so you can wind an extra 10 or 20 feet from pole to tip. That way, if you break the line, you've always got some extra you can unwrap so you can keep fishin'. Another secret is “duct tape”. Tear off a few strips and wrap it around the line along the shaft and that way your extra line doesn't creep off the end and tangle up. Tangled lines are a fisherman's mortal enemy. With the cane pole, simple is best.

Leave enough line hanging from the end of your pole so that from the tip to the hook end of the line reaches just short of the end of the pole. Tie on a fishook large or small enough for the size fish you’re after. Six inches above the hook, tie on a 1 ounce weight. Figure out the depth you want the hook to hang and attach the float or “bobber” to the line. If you find you need to shorten your line for some reason, simply roll the excess up onto the poll.

Now hook on a worm and drop the line into a likely spot. Watch the bobber and if it goes under, give the line a quick tug to set the hook. When you have a fish on the line, simply lift the tip up till the hook comes out of the water with fish attached. Since the line is actually shorter than the pole, all you have to do is bring the pole up vertical and the fish will swing right into your waiting hand. Easy peasy!

Tuesday, November 24, 2009

Flat Canoe Rack

Easy Canoe Rack for Lakeside

This easy to build canoe and kayak rack is simple to build and use, though it does take up a little more space than some of the other designs I've posted here.  It's pretty easy to build:

1.  Dig 4 post holes.  Each pair to which you will bolt a cross member should be as wide apart as you want the rack to be (3 feet times the number of canoes you have).  Put the pairs about 9 or 10 feet apart. That's half to two-thirds the length of most canoes and kayaks and supports well enough so that summer heat doesn't cause the boats to sag and distort the hulls.  Use treated posts. They should stick up about 2 to 3 feet depending on your comfort level and be treated.  Pour concrete around them to set the posts.

2. Lag bolt a 2x12 pressure treated cross member to the posts as shown in the picture.  Pad the cross member to protect the boat.  I like to buy used fire hose from local volunteer fire departments and screw it on top of the cross members n accordion pleats. The pleats keep the canoes from sliding around on the rack.

3. The canoes sit upside down on the cross members. You can mix canoes and kayaks. If you get more canoes than you planned you can nest them and get more canoes on the rack.

4. To make tie-down easier, screw some eyelets to the face of the cross members to create attachment points for bungee cords.  Tying down the canoes prevents them from taking flight in a wind storm.

Sunday, November 15, 2009

Rope-Making

This is how the pros do it. This UK factory makes ropes and cables for the British Navy.

The ancient art of rope-making is a skill that not many people possess anymore.  It’s not really hard to do though once you get your head around the principle.  First you’ll need a a rope-making machine.  Here’s how to build one.  Once you’ve you’ve got one you can whip up lots of rope from light cord to massive hawsers.  It’s actually a lot of fun, especially if you drag a couple of grandkids into it.  You’ll need three people to make a rope.

The Sleds

You are going to build two sleds as shown in the pictures to the right.  They are simple wooden sawhorse-like affairs with skids on the bottom and a seat for the rope turners who act as both rope twisters and ballast.  Build a frame on one end of the sled with a 2 foot by 2 foot flat ¾ inch plywood plate for setting the hooks and cranks.  Build both sleds alike.  One will have 3 hooks and one will only have one. Start with the 3 hook  individual strand twister.  Drill 3 holes at the corners of an equilateral triangle with 10 inch legs.  Make sure it’s centered.  You’ll need room to turn the cranks.

The Strand Twister.

You’ll need 3 steel rods about 12 inches long.  Bend them into a ‘Z’ shape with equal length sections.  The rods must be identical to crank together.  The center section must not be more than 4 inches in length in order to crank freely without bumping into each other.  Insert one end of the “Z” into the three holes in the end plate so the crank part is on the .  Allow them to hang down. 


Next you’ll need to thread about 3 inches of the crank ends so you can bolt the crank plate in place. 

Cut a triangular plywood plate about 12 inches on a side and cut 3 holes 10 inches apart.  They must match the holes in the end plate for this to work.  Thread bolts and washers over the end of the cranks and slip the crank plate over the ends.




Bolt the plate in place with a double nut so the plate will turn freely. A double nut are two nuts on the same side twisted against each other. It's advisable to also put a washer between the nuts and the wooden crank plate.


Finally, you’ll need to a attach a handle to the center of the crank plate in order to turn the hooks.  When you crank the plate, the three hooks will turn together at the same speed.







Now you need to heat and bend the other end of the cranks to make 3 hooks.  These will turn when you crank the opposite end. You'll need a torch to do this. Another way to attach hooks to the end is to thread the ends of the crank rods and screw an eye hook onto the rods backed by double nuts to hold the screw eyes in place so it turns with the crank rods. You can do the bending of the rods and threading ahead of time, but you'll have to enlarge the holes in the hook plate so the Z ends can negotiate the turn. To do this you'll need a piece of pipe to act as guide for the rods. To pull that off you'll have to figure the size of the pipe that will fit the rods, Cut three pieces to match the depth of the holes. Slide them on the rod before you bend the Z ends of the rods. Slide the rods through the holes then slide the pipes into the holes behind them. That way the crank will turn easily, especially if you squirt a little oil into them before working the crank. 














The Rope Twister

For this you’ll need another 3/8 in steel rod bent to an identical “Z” as on the first sled.  Drill a hole in the center of the end plate, insert the crank, thread the crank end and screw on some sort of handle. Fashion a pipe guide like the ones above. Slide it on the rod before you bend the crank. On the opposite end, bend the rod into a hook facing away from the sled seat. Insert the Z end of the crank first with the pipe guide on the hook side. Once the crank is in, pound the pipe into the crank hole and Voila!  Now you have the two sleds.  You only need one more tool.

Spreader

Make another ten inch equilateral plywood triangle with a notch in the center of each side. The spreader separates the strands into their individual parts. It guides the rope strands as they are twisted while you walk beside the ropes keeping them apart as they twist together naturally. You'll start from the hook end and walk toward the triple crank end.






 Rope-Making Materials

You’ll need nylon or grass/hemp bailing twine from which to make the strands.  Tie one end of the ball to the single hook and start stringing loops back and forth to one of the three hooks.  10 strands of twine per hook is a good thickness to practice on.  It will make a thirty strand rope. 




Depending on the thickness of the rope you want, string an equal number of strands of twine between the single hook and each of the three twister hooks. Fit the spreader board between each strand and push it back next to the single hook.



Tensioning the Strands
 
You’ll need 3 people to make a rope - one on the 3 strand crank, one on the single hook and one on the spreader board.  Place the sleds about a third farther apart than the length of rope you want to make. Begin cranking the three hooks clockwise as you face the crank.  Continue until the strands become tight and begin to twist.



 While the person on the 3 hook sled keeps steady pressure on the crank, the person on the single hook needs to gently begin turning the single crank counterclockwise rotating toward the same direction the strands were twisted.  As he turns the single hook, the person on the spreader board moves the board toward the three hook sled allowing the rope to twist itself from the single hook end.  Both crankers should keep steady pressure on the cranks turning them so the strands lay themselves naturally and evenly. The tighter you keep the strands twisted as you you put them together, the tighter the rope will lay up and the better quality it will be.



When you’re close to the end, remove the spreader and tighten all the way down to the triple hooks.  Wrap the ends of the rope with duct tape to keep it from unraveling or wrap fine cord around the end.  Cut the rope loose from the hooks with a sharp knife and coil it up for storage. 

Make yourself a big old hawser if you want and take it to the next family reunion for the tug of war competition.  Brag on it if you want. After all, who else do you know that can make his own rope.



© 2009 by Tom King




Friday, November 13, 2009

Splicing the Main Brace

Repairing A Broken Rope
by Tom King (c) 2009


I broke my heavy three-strand grass tow rope pulling my son's truck home after it broke down. Even a heavy rope will break if someone stomps on the brakes suddenly while someone else keeps sailing merrily on down the road.  Don't ask!  It's a very sad story.

So how to restore the lost length to my rope without weakening it, you ask.  It's an old sailor's trick, once used by ancient mariners to repair a parted main brace, halyard or mainsheet.  So without further "Yo-Ho-Ho" here's how to do it up right.

First lay out the broken rope.

Next use a sharp knife to trim the ends neatly.


Next untwist 4 to 6 inches of strands.


Butt the ends together and put the strands of the first rope (on the left) between the strands of the second rope (on the right).


Pick a strand of the first rope and put it over the strand of the second rope immediately to it's left and then under the next strand to the left. 


Do the same with the next strand on the first rope - over the next strand and under the one after that.


Tuck the third strand over and under as shown to complete the first row.


When you complete the first row, tucking in all three strands, simply do the same thing again with a second row.

When you get to the end of the second row, if you still have enough strand left, tuck in another row until you have the strand tucked in as far as possible.

When the last strand is tucked in, you'll need to pull the rope to set the strands.

Pull the rope tight to set the strands before starting on the strands of the second rope.


Tuck a strand of the second rope over the strand from the first rope that lies next to it and under the rope strand just to the left of that one.


Do the same with the second strand.....



Once all three are tucked under to make the first row of splices, start the next round.


Once all the strands are braided, pull both ends of the ropes to set the splice.


Tape the ends of the splices with a couple of wraps of duct tape.



The spliced section will be as strong or stronger than the original rope, forms a solid connection between the two ropes without a bulky knot. 


When you're all done, you have my permission to beat your own chest and do your Tarzan yell!  Well done, O' Lord of the Jungle.

Wednesday, November 11, 2009

Fake Rocks & Boulders



Making Artificial Rocks
(c) 2009 Some Rights Reserved
by Tom King


A friend of mine makes his living building rocks and designing exhibits for zoos and theme parks. Billy Williamson’s notable work is incredibly lifelike and graces zoos and theme parks all over the country. He kept pestering me to come and help him work on a structure he called a "feed lot for Rose Queens". The structure was a backyard waterfall, stream and swimming pool in the backyard of a local member of Tyler, Texas high society. The waterfall includes a Batcave-style garage underneath the falls where the owner planned to store his Bentley. I finally agreed to join his crew for an afternoon and found myself in welding gloves with an odd bending tool, bending and tying ¼ inch rebar in the Texas summer sun. I was sore for a week. What I learned:


Base


The first part of building artificial rocks is to create the basic shape. You do that by driving rebar into the earth and then using a bending tool to create the skeleton of the rocks and boulders you plan to construct. The vertical rebar, once bent is cross braced by laying horizontal rows of light rebar tide at the point where the bars cross. The tying is tedious, but if you use standard tie wires and a wire tying tool, you can make pretty quick progress. So long as you keep the bars close together and don’t make gaps too large, it’s pretty hard to mess things up. Leave room under the rocks to crawl around under there because you will need to place plastic sheeting behind the rebar.



Backing

Attach heavy gauge plastic sheeting behind the rebar. Use wire ties to pull the plastic up against the rebar to prevent pooling of concrete behind the rebar. Be careful not to rip the plastic. Duct tape can be used to cover tears and holes.

Chicken Wire


Chicken wire makes a perfect framework for the surfaces of artificial rocks. It is shapable, easily cut and quickly attached to the rebar framework. Once all the surface of the structure is covered with chicken wire, go back and tweak the shape a little. Make boulder shapes, cracks, crevices and ledges as you go. Use your creativity. You can even create artificial tree stumps, fallen logs and other natural looking bulky structures.

Concrete

There are two ways of applying the concrete. Lightweight vermiculite or gunite normally used in swimming pools and decks works very well here. The only problem with using a pump, you have to finish the job in one go. For large jobs, this may not leave adequate time to do basic sculpture. To get the proper look for rocks, mix gunite or vermiculite concrete in a wheel barrow and trowel it onto the wire frame. You’ll have to play with the thickness of the mixture to insure it penetrates the wire and rebar without being so thin it is runny. Build up a layer that is at least an inch an a half to 3 inches thick and smoothly covers the rebar and chicken wire. In some places the coating of concrete will be thicker to fill gaps between the chicken wire and rebar. Make sure the rebar below is covered so the rock formation will be strong. Use a flat trowel to smooth the surfaces into the basic rock shape. Do a section as large a section as you can do in half the time you have for the day. Work from the bottom up and apply gently so as not to break through the underlying layer..


Surfacing


When the first layer is partially cured, mix up  a sand aggregate concrete mixture (the kind used for stucco walls and similar surfaces and start at the beginning of the base section you just did. Spread a thin layer of wet finish over the concrete base. You may mix rock colored surface stain in with the mixture or spray coat it on later if you have any special effects in mind. Cover the surfaces of the concrete shapes completely.  Go section by section so your working surface doesn't dry before you can texture it.


Texture

Next, cover the large flat areas with aluminum foil. Do not crumple the foil, but wrinkle it just a little bit and then spread it over the still wet ‘rock’ surfaces and press down firmly as shown in the picture. The foil will give the ‘rock’ surfaces a natural texture.

Cracking


After about 5 minutes, remove the foil and use the edge of the trowel to etch a few cracks into the concrete and to trace seams and layers between separate rock shapes. This takes a steady hand, but don’t make the lines too straight either. Vary depth and width of surface striations to imitate features of natural rock. Lightly brush the rock surface with a paint brush to remove concrete crumbs and create a weathered look. Allow the concrete to set overnight before putting weight on it.

Finish


Once the “rocks” are set and dried, brush or spray on stain. Even if you applied stain to the finish itself, you should add contrasting colors to accent cracks, seams and shadows. It requires an artist’s eye and a lot of practice as you can see from these shots of Billy Williamson’s finished projects. It’s an art form and if you ever get a chance to work with someone like Billy who understands it, take the job! Mimicking Mother Nature is a whole bunch of fun!


This is one of the exhibits at Tiger Creek Wildlife Refuge that Billy designed and help build (below).  Tiger Creek is home to a large collection of rescued tigers, tiger cubs and other big cats located just north of Tyler, Texas.  Tiger Creek is a not for profit organization providing rescue services and shelter care for tigers and big cats.

These tigers below are enjoying the summer sun sprawled on the waterfalls and rocks built by Billy and the volunteer crew and Tiger Creek staff.


 These guys play rough, but the rock formations can handle the pounding.

 This next exhibit was built for a Tennessee zoo by, also by Billy Williamson.  The black bear in the exhibit enjoys the waterfall and stream in his new home.



This fat bear is having a little soak.  Not a single rock here is real.  All were sculpted by hand using the method described above as was the creek below in a chimpanzee exhibit.

Note, there is not a single loose item in the picture below.  Chimpanzees love to throw rocks and loose objects.  Billy's knowledge of chimp behavior led to this design in which everything in the river is part of a single piece of concrete, sculpted and staied to look like an ordinary stream full of rocks and deadfall trees, but without the hazard to keepers and visitors of having a loose rock heaved at you by a mischievous chimp.

Photos (c) 2009 by Tom King, Tiger Creek Wildlife Refuge and Billy Williamson (All Rights Reserved) 


Tuesday, November 10, 2009

Yak on the Rack

Luggage Rack / Kayak Rack Conversion
 by Tom King

Canoes are easy to strap on your SUV’s luggage rack.  Flip them over and the gunwhales rest flat on top of the crossbars and it’s a simple matter of bungee cording the canoe down tight.  Kayaks have curved decks and curved bottoms, so they don’t strap down flat.  You want to create a padded cradle for the kayak to rest in.  Fortunately, it is really simple to make one your self in a few minutes.

What You’ll need

You’ll need two foam swim “noodles” – the kind with the hole down the middle.  You’ll also need a roll of duct tape, a sharp knife and 4 zip ties.

Step 1

Cut the two foam noodles to the width of the luggage rack on top of your truck.

Step 2

Mark a line down the center section leaving about a foot to a foot and a half on either end.  Use your knife to cut through the noodle to the center hole.  Cut along the marked line from the outside to the hole. Don’t cut more than halfway through the noodle. Stop at the end of the mark, leaving the two ends uncut for 12 to 18 inches from the end

Step 4
Wrap the ends of the noodles with duct tape to prevent the cut in the center from splitting down to the ends.

Step 5
Open up the noodle and wrap the open part over the luggage rack crossbar as shown.

Step 6
Zip tie the noodle in place as shown so that the center is down over the crosspar and the ends are curled up to form a padded cradle for the kayak.

Step 7
Now simply rest the hull of the kayak in the foam cradle and bungee cord it tight to the rack.

When you want to remove the cradles, simply clip the zip ties. You’ll zip tie it back in place next time you take the kayak out..

Have fun!










Tom
© 2009 Some rights reserved